5
|
1 /*
|
|
2 * SpanDSP - a series of DSP components for telephony
|
|
3 *
|
|
4 * fcf.h - ITU T.30 fax control field definitions
|
|
5 *
|
|
6 * Written by Steve Underwood <steveu@coppice.org>
|
|
7 *
|
|
8 * Copyright (C) 2003 Steve Underwood
|
|
9 *
|
|
10 * All rights reserved.
|
|
11 *
|
|
12 * This program is free software; you can redistribute it and/or modify
|
|
13 * it under the terms of the GNU General Public License version 2, as
|
|
14 * published by the Free Software Foundation.
|
|
15 *
|
|
16 * This program is distributed in the hope that it will be useful,
|
|
17 * but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
18 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
19 * GNU General Public License for more details.
|
|
20 *
|
|
21 * You should have received a copy of the GNU General Public License
|
|
22 * along with this program; if not, write to the Free Software
|
|
23 * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
|
|
24 *
|
|
25 * $Id: t30_fcf.h,v 1.9 2006/10/24 13:45:28 steveu Exp $
|
|
26 */
|
|
27
|
|
28 /*! \file */
|
|
29
|
|
30 #if !defined(_T30_FCF_H_)
|
|
31 #define _T30_FCF_H_
|
|
32
|
|
33 /*! Initial identification messages */
|
|
34 /*! From the called to the calling terminal. */
|
|
35 #define T30_DIS 0x80 /*! Digital identification signal */
|
|
36 #define T30_CSI 0x40 /*! Called subscriber identification */
|
|
37 #define T30_NSF 0x20 /*! Non-standard facilities */
|
|
38
|
|
39 /*! Commands to send */
|
|
40 /*! From a calling terminal wishing to be a receiver, to a called terminal
|
|
41 which is capable of transmitting. */
|
|
42 #define T30_DTC 0x81 /*! Digital transmit command */
|
|
43 #define T30_CIG 0x41 /*! Calling subscriber identification */
|
|
44 #define T30_NSC 0x21 /*! Non-standard facilities command */
|
|
45 #define T30_PWD 0xC1 /*! Password */
|
|
46 #define T30_SEP 0xA1 /*! Selective polling */
|
|
47 #define T30_PSA 0x61 /*! Polled subaddress */
|
|
48 #define T30_CIA 0xE1 /*! Calling subscriber internet address */
|
|
49 #define T30_ISP 0x11 /*! Internet selective polling address */
|
|
50
|
|
51 /*! Commands to receive */
|
|
52 /*! From a calling terminal wishing to be a transmitter, to a called terminal
|
|
53 which is capable of receiving. */
|
|
54 #define T30_DCS 0x82 /*! Digital command signal */
|
|
55 #define T30_TSI 0x42 /*! Transmitting subscriber information */
|
|
56 #define T30_NSS 0x22 /*! Non-standard facilities set-up */
|
|
57 #define T30_SUB 0xC2 /*! Subaddress */
|
|
58 #define T30_SID 0xA2 /*! Sender identification */
|
|
59 /*! T30_TCF - Training check is a burst of 1.5s of zeros sent using the image modem */
|
|
60 #define T30_CTC 0x12 /*! Continue to correct */
|
|
61 #define T30_TSA 0x62 /*! Transmitting subscriber internet address */
|
|
62 #define T30_IRA 0xE2 /*! Internet routing address */
|
|
63
|
|
64 /*! Pre-message response signals */
|
|
65 /*! From the receiver to the transmitter. */
|
|
66 #define T30_CFR 0x84 /*! Confirmation to receive */
|
|
67 #define T30_FTT 0x44 /*! Failure to train */
|
|
68 #define T30_CTR 0xC4 /*! Response for continue to correct */
|
|
69 #define T30_CSA 0x24 /*! Called subscriber internet address */
|
|
70
|
|
71 /*! Post-message commands */
|
|
72 #define T30_EOM 0x8E /*! End of message */
|
|
73 #define T30_MPS 0x4E /*! Multipage signal */
|
|
74 #define T30_EOP 0x2E /*! End of procedure */
|
|
75 #define T30_PRI_EOM 0x9E /*! Procedure interrupt - end of procedure */
|
|
76 #define T30_PRI_MPS 0x5E /*! Procedure interrupt - multipage signal */
|
|
77 #define T30_PRI_EOP 0x3E /*! Procedure interrupt - end of procedure */
|
|
78 #define T30_EOS 0x1E /*! End of selection */
|
|
79 #define T30_PPS 0xBE /*! Partial page signal */
|
|
80 #define T30_EOR 0xCE /*! End of retransmission */
|
|
81 #define T30_RR 0x6E /*! Receiver ready */
|
|
82
|
|
83 /*! Post-message responses */
|
|
84 #define T30_MCF 0x8C /*! Message confirmation */
|
|
85 #define T30_RTP 0xCC /*! Retrain positive */
|
|
86 #define T30_RTN 0x4C /*! Retrain negative */
|
|
87 #define T30_PIP 0xAC /*! Procedure interrupt positive */
|
|
88 #define T30_PIN 0x2C /*! Procedure interrupt negative */
|
|
89 #define T30_PPR 0xBC /*! Partial page request */
|
|
90 #define T30_RNR 0xEC /*! Receive not ready */
|
|
91 #define T30_ERR 0x1C /*! Response for end of retransmission */
|
|
92 #define T30_FDM 0xFC /*! File diagnostics message */
|
|
93
|
|
94 /*! Other line control signals */
|
|
95 #define T30_DCN 0xFA /*! Disconnect */
|
|
96 #define T30_CRP 0x1A /*! Command repeat */
|
|
97 #define T30_FNV 0xCA /*! Field not valid */
|
|
98 #define T30_TNR 0xEA /*! Transmit not ready */
|
|
99 #define T30_TR 0x6A /*! Transmit ready */
|
|
100 #define T30_PID 0x6C /*! Procedure interrupt disconnect */
|
|
101
|
|
102 /*! Something only use as a secondary value in error correcting mode */
|
|
103 #define T30_NULL 0x00 /*! Nothing to say */
|
|
104
|
|
105 /*! Information frame types used for error correction mode, in T.4 */
|
|
106 #define T4_FCD 0x06 /*! Facsimile coded data */
|
|
107 #define T4_RCP 0x86 /*! Return to control for partial page */
|
|
108
|
|
109 #endif
|
|
110 /*- End of file ------------------------------------------------------------*/
|